JBD 4s (12 Volt) BMS Units |
||
---|---|---|
Basic Properties | ||
Model | 150A | |
Cell Chemistry | LiFePO4 (LFP) | |
Pack Structure | 4s (12.8v Nominal) | |
Nominal Voltage Per Cell | 3.2v | |
Operation Mode | Common Port | |
Number of Temperature Sensors |
2 External (Battery Temp)
1 Internal (MOSFET Temp)
|
|
Cell Monitoring Harness Wire Guage | 24 AWG | |
P- / C- Connection Type |
M6 Threaded Terminal
2 each (4 total)
|
|
Default Charge Protection Parameters | ||
Rated Continuous Charge Current | 150A | |
Charge Over-Current Protection
Trip Delay: 10 seconds
|
Trip: 160A
Release: 32 second delay
|
|
Cell Over-Charge Protection
Trip Delay: 2 seconds
|
Trip: 3.65v
Release: 3.5v
|
|
Pack Over-Charge Protection
Trip Delay: 2 seconds
|
Trip: 14.6v
Release at 14.0v
|
|
High-Temperature Protection
Trip Delay: 2 seconds
|
Trip: 65°C (146°F)
Release: 55°C (131°F)
|
|
Low-Temperature Protection
Trip Delay: 2 seconds
|
Trip: 0°C (32°F)
Release: 5°C (41°F)
|
|
Default Discharge Protection Parameters | ||
Rated Continuous Discharge Current | 150A | |
Discharge Over-Current Protection
Trip Delay: 10 seconds
|
Trip: 160A
Release: 32 second delay
|
|
Cell Over-Discharge Protection
Trip Delay: 2 seconds
|
Trip: 2.5v
Release: 2.75v
|
|
Pack Over-Disharge Protection
Trip Delay: 2 seconds
|
Trip: 10v
Release at 12v
|
|
High-Temperature Protection
Trip Delay: 2 seconds
|
Trip: 75°C (167°F)
Release: 65°C (146°F)
|
|
Low-Temperature Protection
Trip Delay: 2 seconds
|
Trip: -20°C (-4°F)
Release: -10°C (14°F)
|
|
Short-Circuit Protection
Trip Delay: 400µs
|
Trip: 890A
Release: 5 second delay
|
|
Default Cell-Balancing Parameters | ||
Balance Type | Passive Balancing | |
Balance Start Cell Voltage | 3.40v | |
Balance Accuracy |
15mv (0.015v)
Adjustable 0-250mv
|
|
Additional Features & Parameters | ||
|
All parameters are adjustable. Most parameters may be easily adjusted via the Bluetooth app, however, some adjustments may only be made through the PC programming software.
All parameters have a tolerance of ± 2%
Full Feature List:
- Includes USB Monitoring & Programming Cable for customizing setpoints and extended status monitoring.
- Over Voltage Protection: If any cell(s) in your pack exceeds a safe voltage, the BMS will stop charging current from passing through, but will allow loads to draw power from the BMS without needing to be manually reset. The BMS will automatically reset when voltages fall back within a safe range allowing for charging.
- Under Voltage Protection: If any cell cells(s) in your pack fall below a safe voltage, the BMS will stop power from being removed from your battery pack, while simultaneously allowing charge current to enter to bring the cells above the minimum safe voltage.
- Over Current & Short Circuit Protection: If you accidently draw too much power from your batteries, the BMS will interrupt this current, preventing damage to your batteries.
- Under Temperature Protection: LiFePO4 batteries cannot be charged below 0° C (32° F). This BMS will disable charging when temperatures are too low, and automatically re-enable charging when temperatures are back within safe limits. Limits may be adjusted using USB Programming Cable.
- Over Temperature Protection: This BMS will completely turn off if the temperature probe(s) detect temperatures in excess of 75° C (167°F), preventing damage to batteries in high-heat applications.


